Grove Base HAT for Raspberry Pi를 사용해 봤습니다.
8438 단어 RaspberryPiGrovegrovepi
Bazaar 가격은 9.90달러입니다.자주 사용하는 GrovePi+는 29.99달러이기 때문에 3분의 1의 가격이다.
제품이 배달되었기 때문에 바로 치즈파이를 착용해 보세요.
포장
그 전에는 평소에 보지 않고 포장부터 확인해 보세요.
작은 세로 길이의 상자에 제품 이름과 제품 사진이 붙어 있다.
사진에 라즈베리 파이가 포함되지 않아서 그런지.쓰다
뒷면에 Output Voltage와 Grove는 Digital x6, Analog x4, I2Cx3, UART x1, PWM x1이라고 쓰여 있다.
GrovePi+는 5V계입니다. 이것은 3.3V계인 것 같습니다.조심해.
제품
기판 표면에 Grove 연결기가 촘촘하게 설치되어 있다
Grove 커넥터를 제외한 부품이 게재되지 않았습니다.
기판 뒷면에는 바늘 콘센트, 칩 콘덴서, 칩 저항, STM32F030만 탑재되어 있다.
STM32F030은 A/D 변환기로 사용됩니다.
설치
Raspberry Pi 3 Model B 설치!
GrovePi+는 라즈파의 기판 사이즈에서 튀어나왔지만 이것은 라즈파와 똑같이 크다.
카메라와 모니터 케이블을 끌어낼 수 있는 모양과 구멍이 준비되어 있다.
고무 파이의 기판과의 거리는 11mm이다.
간격을 맞추기가 좀 힘들죠?
이렇게 생각하니 편지에 첨부되었다.(-.-)
외관상 이게 GrovePi+보다 좋아요.(개인적인 의견일 뿐)
소프트웨어 설치
제품 위키백과 빠른 설치와 단계별 설치 두 가지 방법을 설명합니다.
빠른 설치를 시도해 보세요.pi@raspberrypi:~ $ curl -sL https://github.com/Seeed-Studio/grove.py/raw/master/install.sh | sudo bash -s -
deb https://seeed-studio.github.io/pi_repo/ stretch main
Warning: apt-key output should not be parsed (stdout is not a terminal)
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 3822 100 3822 0 0 12138 0 --:--:-- --:--:-- --:--:-- 12171
OK
Enable I2C interface ...
I2C interface enabled...
Hit:1 http://archive.raspberrypi.org/debian stretch InRelease
Hit:2 http://raspbian.raspberrypi.org/raspbian stretch InRelease
Get:3 https://seeed-studio.github.io/pi_repo stretch InRelease [3,167 B]
Get:4 https://seeed-studio.github.io/pi_repo stretch/main armhf Packages [29.8 kB]
...
The following additional packages will be installed:
libjson-c3
The following NEW packages will be installed:
libjson-c3 libmraa1
0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded.
...
The following additional packages will be installed:
libpython2.7
The following NEW packages will be installed:
libpython2.7 python-mraa
0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded.
...
The following additional packages will be installed:
libupm1
The following NEW packages will be installed:
libupm1 python-upm
0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded.
...
The following NEW packages will be installed:
python3-mraa
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
...
The following NEW packages will be installed:
python3-upm
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
...
The following NEW packages will be installed:
python3-rpi.gpio
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
...
Preparing to unpack .../python3-rpi.gpio_0.6.5~stretch-1_armhf.deb ...
Unpacking python3-rpi.gpio (0.6.5~stretch-1) ...
Setting up python3-rpi.gpio (0.6.5~stretch-1) ...
main: line 122: pip: command not found
main: line 123: pip: command not found
main: line 122: pip: command not found
main: line 123: pip: command not found
main: line 122: pip: command not found
main: line 123: pip: command not found
-------------------------------------------------------
Grove.py installation FAILED, FAILED, FAILED
-------------------------------------------------------
pi@raspberrypi:~ $
저기, pip는command not found입니다.
pip 설치 후pi@raspberrypi:~ $ sudo apt install python-pip
다시 빠르게 설치합니다.pi@raspberrypi:~ $ curl -sL https://github.com/Seeed-Studio/grove.py/raw/master/install.sh | sudo bash -s -
...
main: line 122: pip3: command not found
main: line 123: pip3: command not found
main: line 122: pip3: command not found
main: line 123: pip3: command not found
main: line 122: pip3: command not found
main: line 123: pip3: command not found
-------------------------------------------------------
Grove.py installation FAILED, FAILED, FAILED
-------------------------------------------------------
pi@raspberrypi:~ $
아이고.
pip3 설치pi@raspberrypi:~ $ sudo apt install python3-pip
다시 빠르게 설치합니다.pi@raspberrypi:~ $ curl -sL https://github.com/Seeed-Studio/grove.py/raw/master/install.sh | sudo bash -s -
...
#######################################################
Lastest Grove.py from github install complete !!!!!
#######################################################
pi@raspberrypi:~ $
성공!!!
실행
PWM이 적힌 Grove 커넥터에 Grove - Buzzer 연결하여 grove_pwm_버저를 실행할 때 삐삐 소리가 났다.grove_
를 입력한 후 연결TAB
키를 누르면 준비된 예시 프로그램이 열거됩니다.
총결산
기판 표면에 Grove 연결기가 촘촘하게 설치되어 있다
Grove 커넥터를 제외한 부품이 게재되지 않았습니다.
기판 뒷면에는 바늘 콘센트, 칩 콘덴서, 칩 저항, STM32F030만 탑재되어 있다.
STM32F030은 A/D 변환기로 사용됩니다.
설치
Raspberry Pi 3 Model B 설치!
GrovePi+는 라즈파의 기판 사이즈에서 튀어나왔지만 이것은 라즈파와 똑같이 크다.
카메라와 모니터 케이블을 끌어낼 수 있는 모양과 구멍이 준비되어 있다.
고무 파이의 기판과의 거리는 11mm이다.
간격을 맞추기가 좀 힘들죠?
이렇게 생각하니 편지에 첨부되었다.(-.-)
외관상 이게 GrovePi+보다 좋아요.(개인적인 의견일 뿐)
소프트웨어 설치
제품 위키백과 빠른 설치와 단계별 설치 두 가지 방법을 설명합니다.
빠른 설치를 시도해 보세요.pi@raspberrypi:~ $ curl -sL https://github.com/Seeed-Studio/grove.py/raw/master/install.sh | sudo bash -s -
deb https://seeed-studio.github.io/pi_repo/ stretch main
Warning: apt-key output should not be parsed (stdout is not a terminal)
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 3822 100 3822 0 0 12138 0 --:--:-- --:--:-- --:--:-- 12171
OK
Enable I2C interface ...
I2C interface enabled...
Hit:1 http://archive.raspberrypi.org/debian stretch InRelease
Hit:2 http://raspbian.raspberrypi.org/raspbian stretch InRelease
Get:3 https://seeed-studio.github.io/pi_repo stretch InRelease [3,167 B]
Get:4 https://seeed-studio.github.io/pi_repo stretch/main armhf Packages [29.8 kB]
...
The following additional packages will be installed:
libjson-c3
The following NEW packages will be installed:
libjson-c3 libmraa1
0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded.
...
The following additional packages will be installed:
libpython2.7
The following NEW packages will be installed:
libpython2.7 python-mraa
0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded.
...
The following additional packages will be installed:
libupm1
The following NEW packages will be installed:
libupm1 python-upm
0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded.
...
The following NEW packages will be installed:
python3-mraa
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
...
The following NEW packages will be installed:
python3-upm
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
...
The following NEW packages will be installed:
python3-rpi.gpio
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
...
Preparing to unpack .../python3-rpi.gpio_0.6.5~stretch-1_armhf.deb ...
Unpacking python3-rpi.gpio (0.6.5~stretch-1) ...
Setting up python3-rpi.gpio (0.6.5~stretch-1) ...
main: line 122: pip: command not found
main: line 123: pip: command not found
main: line 122: pip: command not found
main: line 123: pip: command not found
main: line 122: pip: command not found
main: line 123: pip: command not found
-------------------------------------------------------
Grove.py installation FAILED, FAILED, FAILED
-------------------------------------------------------
pi@raspberrypi:~ $
저기, pip는command not found입니다.
pip 설치 후pi@raspberrypi:~ $ sudo apt install python-pip
다시 빠르게 설치합니다.pi@raspberrypi:~ $ curl -sL https://github.com/Seeed-Studio/grove.py/raw/master/install.sh | sudo bash -s -
...
main: line 122: pip3: command not found
main: line 123: pip3: command not found
main: line 122: pip3: command not found
main: line 123: pip3: command not found
main: line 122: pip3: command not found
main: line 123: pip3: command not found
-------------------------------------------------------
Grove.py installation FAILED, FAILED, FAILED
-------------------------------------------------------
pi@raspberrypi:~ $
아이고.
pip3 설치pi@raspberrypi:~ $ sudo apt install python3-pip
다시 빠르게 설치합니다.pi@raspberrypi:~ $ curl -sL https://github.com/Seeed-Studio/grove.py/raw/master/install.sh | sudo bash -s -
...
#######################################################
Lastest Grove.py from github install complete !!!!!
#######################################################
pi@raspberrypi:~ $
성공!!!
실행
PWM이 적힌 Grove 커넥터에 Grove - Buzzer 연결하여 grove_pwm_버저를 실행할 때 삐삐 소리가 났다.grove_
를 입력한 후 연결TAB
키를 누르면 준비된 예시 프로그램이 열거됩니다.
총결산
제품 위키백과 빠른 설치와 단계별 설치 두 가지 방법을 설명합니다.
빠른 설치를 시도해 보세요.
pi@raspberrypi:~ $ curl -sL https://github.com/Seeed-Studio/grove.py/raw/master/install.sh | sudo bash -s -
deb https://seeed-studio.github.io/pi_repo/ stretch main
Warning: apt-key output should not be parsed (stdout is not a terminal)
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 3822 100 3822 0 0 12138 0 --:--:-- --:--:-- --:--:-- 12171
OK
Enable I2C interface ...
I2C interface enabled...
Hit:1 http://archive.raspberrypi.org/debian stretch InRelease
Hit:2 http://raspbian.raspberrypi.org/raspbian stretch InRelease
Get:3 https://seeed-studio.github.io/pi_repo stretch InRelease [3,167 B]
Get:4 https://seeed-studio.github.io/pi_repo stretch/main armhf Packages [29.8 kB]
...
The following additional packages will be installed:
libjson-c3
The following NEW packages will be installed:
libjson-c3 libmraa1
0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded.
...
The following additional packages will be installed:
libpython2.7
The following NEW packages will be installed:
libpython2.7 python-mraa
0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded.
...
The following additional packages will be installed:
libupm1
The following NEW packages will be installed:
libupm1 python-upm
0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded.
...
The following NEW packages will be installed:
python3-mraa
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
...
The following NEW packages will be installed:
python3-upm
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
...
The following NEW packages will be installed:
python3-rpi.gpio
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
...
Preparing to unpack .../python3-rpi.gpio_0.6.5~stretch-1_armhf.deb ...
Unpacking python3-rpi.gpio (0.6.5~stretch-1) ...
Setting up python3-rpi.gpio (0.6.5~stretch-1) ...
main: line 122: pip: command not found
main: line 123: pip: command not found
main: line 122: pip: command not found
main: line 123: pip: command not found
main: line 122: pip: command not found
main: line 123: pip: command not found
-------------------------------------------------------
Grove.py installation FAILED, FAILED, FAILED
-------------------------------------------------------
pi@raspberrypi:~ $
저기, pip는command not found입니다.pip 설치 후
pi@raspberrypi:~ $ sudo apt install python-pip
다시 빠르게 설치합니다.pi@raspberrypi:~ $ curl -sL https://github.com/Seeed-Studio/grove.py/raw/master/install.sh | sudo bash -s -
...
main: line 122: pip3: command not found
main: line 123: pip3: command not found
main: line 122: pip3: command not found
main: line 123: pip3: command not found
main: line 122: pip3: command not found
main: line 123: pip3: command not found
-------------------------------------------------------
Grove.py installation FAILED, FAILED, FAILED
-------------------------------------------------------
pi@raspberrypi:~ $
아이고.pip3 설치
pi@raspberrypi:~ $ sudo apt install python3-pip
다시 빠르게 설치합니다.pi@raspberrypi:~ $ curl -sL https://github.com/Seeed-Studio/grove.py/raw/master/install.sh | sudo bash -s -
...
#######################################################
Lastest Grove.py from github install complete !!!!!
#######################################################
pi@raspberrypi:~ $
성공!!!실행
PWM이 적힌 Grove 커넥터에 Grove - Buzzer 연결하여 grove_pwm_버저를 실행할 때 삐삐 소리가 났다.grove_
를 입력한 후 연결TAB
키를 누르면 준비된 예시 프로그램이 열거됩니다.
총결산
Reference
이 문제에 관하여(Grove Base HAT for Raspberry Pi를 사용해 봤습니다.), 우리는 이곳에서 더 많은 자료를 발견하고 링크를 클릭하여 보았다 https://qiita.com/matsujirushi/items/4d54e076902cbbdd2704텍스트를 자유롭게 공유하거나 복사할 수 있습니다.하지만 이 문서의 URL은 참조 URL로 남겨 두십시오.
우수한 개발자 콘텐츠 발견에 전념 (Collection and Share based on the CC Protocol.)